OEM/ODM Manufacturer Poly-crystalline Solar Panel 200W Kenya Manufacturer
Short Description:
We pursue the management tenet of "Quality is superior, Service is supreme, Reputation is first", and will sincerely create and share success with all clients for OEM/ODM Manufacturer Poly-crystalline Solar Panel 200W Kenya Manufacturer, Contact with us today! We are ready for the market service now!
Poly-crystalline Solar Panel 200W
Technical parameter
Maximum Power(W) 200W
Optimum Power Voltage(Vmp) 26.78V
Optimum Operating Current(Imp) 7.47A
Open Circuit Voltage(Voc) 32.66V
Short Circuit Current(Isc) 8.21A
Mechanical Characteristics
Cell Type Polycrystalline 156x156mm (6 inch)
No of Cell 54 (6x9pcs)
Dimensions 1482x990x40mm
Weight 17.6Kg
Front Glass 3.2mm,High Transmission, Low Iron,Tempered Glass
Junction box IP65 Rated
Output Cable TUV 1×4.0mm2/UL12AWG,Length:900mm
Temperature and Coefficients
Operating Temperature(°C): -40°C ~ + 85°C
Maximum System Voltage: 600V(UL)/1000V(IEC) DC
Maximum Rated Current Series: 15A
Temperature Coefficients of Pmax: -0.47%
Temperature Coefficients of Voc: -0.389%
Temperature Coefficients of Isc: 0.057%
Nominal Operationg Cell Temperature (NOCT): 47+/-2°C
Materials of solar panel
1).Solar Cell——Polycrystalline solar cell 156*156mm
2).Front Glass——-3.2mm, high transmission, low iron, tempered glass
3).EVA——-excellent anti-aging EVA
4).TPT——-TPT hot seal made of flame resistance
5).Frame——anodized aluminum profile
6).Junction Box——-IP65 rated, high quality, with diode protection
Superiority: high quality anodized aluminum frame, high efficiency long life, easy installation, strong wind resistance, strong hail resistance.
Features
1. High cell efficiency with quality silicon materials for long term output stability
2. Strictly quality control ensure the stability and reliability, totally 23 QC procedures
3. High transmittance low iron tempered glass with enhanced stiffness and impact resistance
4. Both Poly-crystalline and Mono-crystalline
5. Excellent performance in harsh weather
6. Outstanding electrical performance under high temperature and low irradiance
Quality assurance testing
Thermal cycling test
Thermal shock test
Thermal/Freezing and high humidity cycling test
Electrical isolation test
Hail impact test
Mechanical, wind and twist loading test
Salt mist test
Light and water-exposure test
Moist carbon dioxide/sulphur dioxide
Can you repair dents in an automobile with a hair dryer and a can of compressed air? Yes and no. It depends upon the location and severity of the damage. But as I have demonstrated, with a heat gun, $9 worth of Endust Duster, and about 15 minutes, you can achieve some remarkable results.
Read more at… http://blog.yagelski.com/2011/10/paintless-dent-repair-using-heat-gun.html
Responses to the most common criticisms:
Q. Why didn’t you just push the dent out from behind?
A. This is a hybrid vehicle and there is A/C equipment for battery cooling that is located between the sheet metal and the interior finish. The dent was simply not accessible from the inside.
Q. Why didn’t you just use a toilet plunger and pull the dent out?
A. That may have worked on the larger of the two dents, but the surface area of the smaller dent would have made that impossible.
Q. This video and photos of the dents have been Photoshopped and faked!
A. Absolutely not. I will gladly attest that this video and the images of the dent, before and after, have not been retouched. I also have a witness who observed the process and would attest the same.
Q. “Tapping” the panel like you did in the video would have popped the dent out without the heating and cooling.
A. My attempts to pop the dent out with persuasive tapping by hand and a rubber mallet prior to the heating / cooling did not have any impact.
Q. This process didn’t help, you can still see the dents!
A. Yes. if you look closely you can still see the smaller of the two dents. However, the larger of the two is not distinguishable to the casual observer. This process made a significant improvement to the appearance of both dents. It is not a factory perfect repair, but this is not a valuable vehicle either. I could not justify the expense of a professional body shop for a vehicle that is seven years old and +150,000 miles. This process provided a good alternative.
[http://www.consulindia.in/] Established in the year 1985, we, Consul Consolidated Pvt. Ltd., are one of the leading manufacturers, exporters and suppliers of a wide range of best quality Solar Power Products and UPS. Offered product range consists of Solar Photovoltaic Modules, Solar Charge Controllers and Solar Energy Storage Systems. With the intention to guarantee that our offered items have the previously stated qualities, we fabricate these by making utilization of value endorsed crude material sourced from authentic vendors.