Factory best selling Mono-Crystalline 180W Solar Panel Manufacturer in Cebu
Short Description:
We always think and practice corresponding to the change of circumstance, and grow up. We aim at the achievement of a richer mind and body and the living for Factory best selling Mono-Crystalline 180W Solar Panel Manufacturer in Cebu, "Create Values,Serving Customer!" is the aim we pursue. We sincerely hope that all customers will establish long term and mutually beneficial cooperation with us.If you wish to get more details about our company, Please contact with us now
Mono-Crystalline 180W Solar Panel
Technical parameter
Maximum Power(W) 180W
Optimum Power Voltage(Vmp) 36.42V
Optimum Operating Current(Imp) 4.96A
Open Circuit Voltage(Voc) 44.45V
Short Circuit Current(Isc) 5.44A
Mechanical Characteristics
Cell Type Mono-crystalline 125x125mm (5 inch)
No of Cell 72 (6x12pcs)
Dimensions 1580x808x35mm
Weight 14.5Kg
Front Glass 3.2mm,High Transmission, Low Iron,Tempered Glass
Junction box IP65 Rated
Output Cable TUV 1×4.0mm2/UL12AWG,Length:900mm
Temperature and Coefficients
Operating Temperature(°C): -40°C ~ + 85°C
Maximum System Voltage: 600V(UL)/1000V(IEC) DC
Maximum Rated Current Series: 15A
Temperature Coefficients of Pmax: -0.47%
Temperature Coefficients of Voc: -0.389%
Temperature Coefficients of Isc: 0.057%
Nominal Operationg Cell Temperature (NOCT): 47+/-2°C
Materials of solar panel
1).Solar Cell——Mono-crystalline solar cell 125*125mm
2).Front Glass——-3.2mm, high transmission, low iron, tempered glass
3).EVA——-excellent anti-aging EVA
4).TPT——-TPT hot seal made of flame resistance
5).Frame——anodized aluminum profile
6).Junction Box——-IP65 rated, high quality, with diode protection
Superiority: high quality anodized aluminum frame, high efficiency long life, easy installation, strong wind resistance, strong hail resistance.
Features
1. High cell efficiency with quality silicon materials for long term output stability
2. Strictly quality control ensure the stability and reliability, totally 23 QC procedures
3. High transmittance low iron tempered glass with enhanced stiffness and impact resistance
4. Both Poly-crystalline and Mono-crystalline
5. Excellent performance in harsh weather
6. Outstanding electrical performance under high temperature and low irradiance
Quality assurance testing
Thermal cycling test
Thermal shock test
Thermal/Freezing and high humidity cycling test
Electrical isolation test
Hail impact test
Mechanical, wind and twist loading test
Salt mist test
Light and water-exposure test
Moist carbon dioxide/sulphur dioxide
Ok, the weather finally cooled off and allowed me to finish the panel. I coated the whole thing in 4 coats of KILZ white sealer. I did not use pegboard for the cell mounting substrate because I didn’t like the holes. I instead used 1/8″ door skin which worked out excellent. I also did not glue the cells down with blobs of silicone. I decided to use 1″ Scotch heavy duty mounting squares which are adhesive on both sides. You just peel the tape off of the outside and stick them down. I am not sure how these will work VS. silicone in the long run, but I experimented with a cell by sticking it onto a scrap piece of door skin and the bond was permanent. I had to destroy the cell to get it off of the scrap piece. So, hopefully they will work. All that is left to do now is get a piece of glass cut, silicone that down and put some aluminum channel on the outside. This entire thing is going to cost around $140 to build. The panel puts out 63 watts, 19.25 volts and 3.63 amps. Not bad.
FOR SALE! Please check our other videos as we have other properties for sale also. If anyone is seriously interested we can forward more info. We don’t check the videos often so please email us if interested.
Write to: [email protected] Serious inquiries only. Please see our other videos for our other properties for sale!
