6 Years Factory Mono-Crystalline 80W Solar Panel Manufacturer in Sydney
Short Description:
The company keeps to the operation concept "scientific management, high quality and efficiency primacy, customer supreme for 6 Years Factory Mono-Crystalline 80W Solar Panel Manufacturer in Sydney, If you are interested in any of our products and services, please don't hesitate to contact us. We are ready to reply you within 24 hours after receipt of your request and to create mutual un-limited benefits and business in near future.
Mono-Crystalline 80W Solar Panel
Technical parameter
Maximum Power(W) 80W
Optimum Power Voltage(Vmp) 15.90V
Optimum Operating Current(Imp) 5.03A
Open Circuit Voltage(Voc) 18.58V
Short Circuit Current(Isc) 5.59A
Mechanical Characteristics
Cell Type Monocrystalline 125x125mm (5 inch)
No of Cell 36 (4x9pcs)
Dimensions 906x670x35mm
Weight 7.2KGS
Front Glass 3.2mm,High Transmission, Low iron, tempered Glass
Junction box IP65 Rated
Output Cable TUV 1×4.0mm2/UL12AWG,Length: 900mm
Temperature and Coefficients
Operating Temperature(°C): -40°C ~ + 85°C
Maximum System Voltage: 600V(UL)/1000V(IEC) DC
Maximum Rated Current Series: 15A
Temperature Coefficients of Pmax: -0.435%
Temperature Coefficients of Voc: -0.35%
Temperature Coefficients of Isc: 0.043%
Nominal Operating Cell Temperature (NOCT): 47+/-2°C
Materials of solar panel
1).Solar Cell——Mono-crystalline solar cell 125*125mm
2).Front Glass——-3.2mm, high transmission, low iron, tempered glass
3).EVA——-excellent anti-aging EVA
4).TPT——-TPT hot seal made of flame resistance
5).Frame——anodized aluminum profile
6).Junction Box——-IP65 rated, high quality, with diode protection
Superiority: high quality anodized aluminum frame, high efficiency long life, easy installation, strong wind resistance, strong hail resistance.
Features
1. High cell efficiency with quality silicon materials for long term output stability
2. Strictly quality control ensure the stability and reliability, totally 23 QC procedures
3. High transmittance low iron tempered glass with enhanced stiffness and impact resistance
4. Both Polycrystalline and Mono-crystalline
5. Excellent performance in harsh weather
6. Outstanding electrical performance under high temperature and low irradiance
Quality assurance testing
Thermal cycling test
Thermal shock test
Thermal/Freezing and high humidity cycling test
Electrical isolation test
Hail impact test
Mechanical, wind and twist loading test
Salt mist test
Light and water-exposure test
Moist carbon dioxide/sulphur dioxide
Here’s my (almost) completed portable solar car stereo. The entire unit is composed of solely car stereo parts, excluding the solar panels. The entire build time was approximately 30+ hours. I actually built this out of inspiration after I saw an “Ion Audio Block Rocker”. I mainly use this during the summer, when I load it on a wagon and bring it on the beach. It attracts a lot of attention, trust me.
Read below for all of the specs. I appreciate any and all feedback. Also, please check out my website if you’re interested….
www.GreenTechNetwork.net
Amp: CrunchPZT900.4. It runs at around 120 watts RMS on each of the four channels. $99
Sub: One Visionik 10 inch. Around 300W RMS If I remember correctly. $59.
Speakers: Two 6×9 Kenwoods. About 95W RMS each. $49 for both.
Battery: One 35 amp deep cycle lead acid battery. $85
Solar panels: One 20 watt panel. Two 5 watt panels. $65 + $30 = $95
Charge controller: One 7 amp SunForce controller. $20
Speaker enclosures: $45+$30=$75.
Wiring, hinges, ect: Approximately $20
Total: $502 and 30+ hours.
Jose Mª nos explica la diferencia técnica de producción entre unos paneles y otros.