23 Years Factory Mono-Crystalline 250W Solar Panel Wholesale to Tanzania

Short Description:


Product Detail

Product Tags

To be the stage of realizing dreams of our employees! To build a happier, more united and more professional team! To reach a mutual benefit of our customers, suppliers, the society and ourselves for 23 Years Factory Mono-Crystalline 250W Solar Panel Wholesale to Tanzania, welcomes all overseas friends and merchants to establish collaboration with us. We will provide you with honest, high quality and efficient service to meet your requirements.


Mono-Crystalline 250W Solar Panel

Technical parameter

Maximum Power(W)                        250W

Optimum Power Voltage(Vmp)        30.3V

Optimum Operating Current(Imp)    8.29A

Open Circuit Voltage(Voc)               36.76V

Short Circuit Current(Isc)                 8.91A

Mechanical Characteristics

Cell Type Monocrystalline                 156x156mm (6 inch)

No of Cell                                         60 (6x10pcs)

Dimensions                                     1640x990x40mm

Weight                                             18.0KGS

Front Glass                                     3.2mm,High Transmission, Low Iron,Tempered Glass

Junction box                                    IP65 Rated

Output Cable                                   TUV 1×4.0mm2/UL12AWG,Length:900mm

Temperature and Coefficients

Operating Temperature(°C):                -40°C ~ + 85°C

Maximum System Voltage:                  600V(UL)/1000V(IEC) DC

Maximum Rated Current Series:         15A

Temperature Coefficients of Pmax:     -0.47%

Temperature Coefficients of Voc:        -0.389%

Temperature Coefficients of Isc:           0.057%

Nominal Operationg Cell Temperature (NOCT): 47+/-2°C

Materials of solar panel

1).Solar Cell——Mono-crystalline solar cell 156*156mm

2).Front Glass——-3.2mm, high transmission, low iron, tempered glass

3).EVA——-excellent anti-aging EVA

4).TPT——-TPT hot seal made of flame resistance

5).Frame——anodized aluminum profile

6).Junction Box——-IP65 rated, high quality, with diode protection

Superiority: high quality anodized aluminum frame, high efficiency long life, easy installation, strong wind resistance, strong hail resistance.

Features

1. High cell efficiency with quality silicon materials for long term output stability

2. Strictly quality control ensure the stability and reliability, totally 23 QC procedures

3. High transmittance low iron tempered glass with enhanced stiffness and impact resistance

4. Both Polycrystalline and Mono-crystalline

5. Excellent performance in harsh weather

6. Outstanding electrical performance under high temperature and low irradiance 

Quality assurance testing

Thermal cycling test

Thermal shock test

Thermal/Freezing and high humidity cycling test

Electrical isolation test 

Hail impact test

Mechanical, wind and twist loading test

Salt mist test

Light and water-exposure test

Moist carbon dioxide/sulphur dioxide

  • Previous:
  • Next:



  • This effect started off as a plain plastic silhouette type Xmas light, with a string of traditional tungsten lamps on it. I made a small inline capacitive dropper as used in many small LED mains powered lamps. It consists of a 100nF 400V capacitor with a 1 Megohm discharge resistor across it, and a 1K half watt resistor in series with a bridge rectifier made up of four 1N4007 diodes. I slid a bit of heatshrink sleeve over the hard wired PSU circuit, hot melt glued one end, and then potted it all in two part resin for safety. The output of the PSU is rectified and current limited mains voltage which lets me run all of the LEDs in series on the UK 240V mains supply. I then removed all the original push-in lamps in the effect and took the glass lamp out of it’s base, replacing the lamp with a bi-colour flashing LED. You can’t use the RGB flashing/fading LEDs in this arrangement because the pulse width dimming means they frequently go open circuit in normal use and with this circuit the open circuit voltage would be high. The LEDs I used flick alternatively between blue and green chips and since one LED is always on they are OK in this application.
    I bent and cropped the leads of the LEDs and also used a pair of snips to crack the lens end of the LED off to give it a wider viewing angle. The irregular fissures of cracking the end off is a good visual effect. I then put the LEDs into the series string of sockets, noting the polarity. You MUST get the polarity right or the LEDs will be damaged with the high reverse voltage.
    The end result is an effect where every point of light alternates between green and blue at its own speed, giving the effect of swirls and waves of colour on the effect.
    The fact the PSU puts out unsmoothed DC meant that these LEDs flickered randomly when exposed to bright light. This is because the chip in the LED is exposed to external light and it affects the stability with rough DC. I tried a 100nF cap across the DC output and it fixed it immediately. However, I kinda liked the wild flickering so didn’t use the cap in the end. The effect works fine in the dark.
    You may notice a duff LED on the left which is missing a colour. These were cheap ebay LEDs and you inevitably get a duffer or two. It’s easy to change them out though.
    I put this up in my window for Xmas. It only draws about a watt of power which is very “eco”.



    Solar panels are being installed on the roof of the Montgomery County Council Office Building at 100 Maryland Avenue in Rockville. The solar energy system is expected to generate more than 53,000 kilowatt hours of energy each year.

    The solar panel project at the Council Office Building is part of a larger Montgomery County initiative to generate clean solar energy on-site at County-owned facilities. With 75 percent of the projects completed, the Solar and Advanced Energy Initiative is on track to bring six megawatts of solar power on line this year. That is enough electricity to power more than 600 single-family homes.

    According to a news release, the County’s solar projects will reduce greenhouse gas emissions equivalent to taking 870 cars off the road or planting 100,000 trees. In addition, the projects will save the County $11 million in energy costs over the next 20 years.

    Montgomery County has fully operating solar energy systems at eleven facilities, including the Gaithersburg Library, the Rockville Library, Potomac Community Center, Jane Lawton Recreation Center in Chevy Chase, the Up-County Regional Services Center in Germantown, the Silver Spring Civic Building, Fire Station No. 31 in North Potomac, the Montgomery County Circuit Court South Tower in Rockville, the Shady Grove Transfer Station, the Montgomery County Department of Liquor Control in Darnestown and the Equipment Maintenance and Transit Operations Center.

    In addition to starting work on the COB solar panels, the County also has started construction on a parking canopy that will support solar panels at the Holiday Park Senior Center in Wheaton. The solar canopy will keep visitors out of the rain, keep their cars cool in the summer heat and provide clean solar energy to the facility.

    Solar installations are also planned for the Montgomery County Correctional Facility in Boyds and for the Kidstop Childcare Center in Rockville.

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Star

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Key

    WhatsApp Online Chat !